Molded Butt Fusion

All IntegriFuse brand HDPE molded Butt fittings, Flange Adapters, & MJ Adapters are Made in the USA and comply with BABA – The Build America, Buy America Act

Integrity Fusion Products offers a full line of injection molded IPS and DIPS HDPE Fittings that are manufactured in a variety of nominal pipe sizes and SDR’s in our manufacturing facility located in Peachtree City, GA. Injection Molded HDPE Fittings, Flange Adapters, and MJ Adapters from Integrity Fusion Products are designed, manufactured, and tested to meet and/or exceed requirements of ASTM D2513, ASTM D3261, and ANSI/AWWA C901 and C906, and FM 1613 (where applicable) for use with outside diameter-controlled polyethylene pipe and fittings conforming to ASTM D2513, ASTM D3035, and ASTM F-714. Integrity Fusion Product Molded HDPE Fittings, Flange Adapters, and MJ Adapters can be heat fused or electrofused to any manufacturers’ PE pipe, molded fittings, or fabricated fittings manufactured from material made from PE3408 / PE4710 / PE100 resin that complies to ASTM D3350.

IntegriFuse Molded fittings ensure more consistent fitting symmetry, and dimensional and wall thickness consistency because each fitting is an injection molded part produced from the same mold repeatedly. Thicker body walls provide the fitting with more integral reinforcement, which allow molded fittings to consistently handle higher pressures, water hammer, and surge pressures. IntegriFuse Molded fittings are designed to operate at the MAOP of the fittings SDR pressure rating and do not have to be de-rated in accordance with ASTM F2206 as fabricated fittings do.

Below is a list of fittings with their size range and SDR listed. Click on the product image for more information and product specifications.

Note: Molded 45°, 90° Elbows, and Equal Tees are now available in Diameter Sizes 14″ – 24″ (see Product Dimension Sheests for specific diameters and SDR’s currently available.)

Elbows

Molded HDPE Elbows are fittings designed to change or redirect the flow of a gaseous or liquid medium in a piping system smoothly and efficiently, while maintaining overall structural integrity.

90º Elbows

Available in Diameters larger than 12″

45º Elbows

Available in Diameters larger than 12″

Tees

HDPE Molded Equal Tees and Reducing Tees are designed to add a service branch of equal size, or to create a branch with a smaller diameter that facilitates the flow of a gaseous or liquid medium in a piping system to be smoothly and efficiently redistributed or diverted while maintaining overall structural integrity of the system.

Equal Tees

Available in Diameters larger than 12″

Reducing Tees

Wyes

HDPE Molded Lateral Wyes are designed to provide a service branch of equal size, utilizing a 45° Y-configuration, with no internal restrictions to impede the flow, that facilitates the movement of a gaseous or liquid medium in a piping system to be smoothly and efficiently redistributed or diverted from the primary line while maintaining overall structural integrity of the system.

Lateral Wyes

Crosses

HDPE Molded Crosses are designed with four openings that intersect at 90-degree angles, allowing for a direct and perpendicular connection between four separate pipes or sections of HDPE piping. The primary function of an HDPE cross fitting is to facilitate the branching of pipelines, creating a junction where fluid flow can be divided or redirected in multiple directions, with no internal restrictions to impede the flow, and that facilitates the flow of a gaseous or liquid medium in a piping system to be smoothly and efficiently redistributed or diverted from the primary line while maintaining overall structural integrity of the system.

Cross

Reducers

HDPE Molded Reducers are designed to transition between pipes with different diameters, with no internal restrictions to impede the flow, and that facilitates the flow of a gaseous or liquid medium in a piping system to be smoothly and efficiently made while maintaining overall structural integrity of the system.

Reducers

Caps

HDPE Molded End Caps are designed to terminate and seal the ends of HDPE pipes with a secure and reliable permanent or temporary seal that prevents leakage in full-pressure applications, while maintaining the functionality and overall structural integrity of the system.